 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TACT SwitchTM 6.2 7.15mm SidepushTM (Snap-in Type) SKRD Series 2pins with simple snap-in package. Detector Push Slide Rotary Encoders Power Dual-in-line Package Type TACT Switch TM Product Line Product No. SKRDLAA010 SKRDLBA010 Operating Operating Travel force direction mm 0.98N Horizontal 1.57N 0.25 Rating max. 50mA 12V DC Rating min. 10BA 1V DC Operating life 5mA 5V DC 100,000cycles Initial contact resistance 100m max. Stem color Black Minimum order unit pcs. 1,000 CustomProducts Dark gray Dimensions Style Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type 4 Unit:mm PC board mounting hole dimensions Viewed from switch mounting face o3.5 6.2 0.3 stem o1 2- 4.5 7.1 0.9 s le ho 1 0.7 1 4.5 2 3.2 0.3 3.85 3.3 6.2 Circuit Diagram Notes 1. Please use 1.6mm thick PC boards. 2. Please use single-sided PC boards. 1 2 Refer to P.306 for soldering conditions. 260 TACT SwitchTM List of Varieties Sharp Feeling Type Series SKHR SKHL SKHH SKHW SKRD SKQJ SKHL SKHH SKQJ SKHJ SKQB Detector Push Type Features Operating direction Vertical Encoders Horizontal Power W Dimensions mm 4.5 6 6 3.5 3.8 4.3 7.15 7.4 5 6.2 6.6 7.22 4.3 7.4 7.85 7.3 8.5 5 7.3 7.5 8 10 Dust-proof Horizontal type type Snap-in Horizontal type With LED Water- proof Photo Slide Rotary D H 1N Dual-in-line Package Type TACT SwitchTM CustomProducts Operation force coverage 5N Ground terminal Operating temperature range Electrical performance Durability Insulation resistance Voltage proof Vibration Lifetime Cold Dry heat Damp heat Page 252 253 255 259 60 2 260 20 to 70 SKHJ/HL Vertical Type /QJ 30 100M to 85 Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type min. 100V DC 250V AC for 1min. 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2hours respectively Shall be in accordance with individual specifications. 30 80 2 2 for 96h for 96h Note The automotive operating temperature range to be individually discussed upon request. Environmental performance , 90 to 95%RH for 96h 261 253 255 261 263 265 W Width. The most outer dimension excluding terminal portion. D Depth. The most outer dimension excluding terminal portion. H Height. The minimum dimension if there are variances. 247 TACT SwitchTM Soldering Conditions Condition for Reflow Available for Surface Mount Type. 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2 Detector Push Slide Rotary Encoders Power CA K or CC T at solder joints copper foil surface . A heat resistive tape should be used to fix thermocouple. 3. Temperature profile Temperature (C ) 260C max. 3 sec max. 180 150 Time 230C Dual-in-line Package Type TACT SwitchTM 40s max. 3 to 4min. CustomProducts Time inside soldering equipment Note 1. The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the material, size, thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type Conditions for Auto-dip Available for Snap-in Type and Radial Type Except SKHJ, SKHL, SKQJ, SKQK, SKEG series Items Flux built-up Condition Mounting surface should not be exposed to fluk Ambient temperature of the soldered surface of PC board. 100 max. 60s max. 260 max. Manual Soldering Except SKRT Series Items Soldering temperature Duration of soldering Capacity of soldering iron Condition 350 max. 3s max. 60W max. Preheating temperature Preheating time Soldering temperature Duration of immersion Number of soldering 5s max. 2times max. Notes 1. 2. 3. 4. 5. Consult with us for availability of TACT SwitchTM washing. Prevent flux penetration from the top side of the TACT SwitchTM. Switch terminals and a PC board should not be coated with flux prior to soldering. The second soldering should be done after the switch is stable with normal temperature. Use the flux with a specific gravity of min 0.81. EC-19S-8 by TAMURA Corporation, or equivalents. 306 |
Price & Availability of SKRDLAA010
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |